含内热源球壳的复合传热特性及其表面温度均匀性研究

应用计算流体动力学方法,对带内热源的空腔球壳所涉及的含导热、自然对流和辐射换热的耦合传热问题进行了数值建模,得到了球壳空腔内、外侧流体的温度场、速度场。在数值模拟基础上,提出并试验验证了能有效提高球壳外表面温度均匀性的电加热绳方案。     

Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

热处理对二次锻造高Nb-TiAl基合金组织的影响

研究了热处理对二次锻造高Nb-TiAl基合金组织的影响。通过对Ti-45Al-9(Nb,W,B,Y)金属间化合物进行不同的热处理,得到不同的显微组织。结果表明,经1310℃/20min+1250℃/2h/AC热处理后,β相被有效地消除,得到细小均匀的双态组织。此后直接加热到α单相区,得到条带状的全片层组织。增加在两相区的停留,得到相对比较均匀细小的全片层组织。将锻造组织先转变为近γ组织再进行全片层组织处理,得到最均匀细小的全片层组织。     

Microstructure and Optical Characterization of Magnetron Sputtered NbN Thin Films

Some fundamental studies on the preparation, structure and optical properties of NbN films were carried out. NbN thin films were deposited by DC reactive magnetron sputtering at different N2 partial pressures and different substrate temperatures ranging from –50 ℃ to 600 ℃. X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM) were employed to characterize their phase com- ponents, microstructures, grain sizes and surface morphology. Optical properties inclusive of refractive indexes, extinction coefficients and transmittance of the NbN films under different sputtering conditions were measured. With the increase in the N2 partial pressure, δ-NbN phase structure gets forming and the grain size and lattice constant of the cubic NbN increasing. The deposited NbN film has relatively high values of refractive index and extinction coefficient in the wavelength ranging from 240 nm to 830 nm. Substrate tem- perature exerts notable influences on the microstructure and optical transmittance of the NbN films. The grain sizes of the δ-NbN film remarkably increase with the rise of the substrate temperature, while the transmittance of the films with the same thickness decreases. Ultra-fine granular film with particle size of several nanometers forms when the substrate is cooled to –50 ℃, and a remarkable aug- mentation of transmittance could be noticed under so low a temperature.     

金属-氟塑料自润滑材料的摩擦磨损特性

对奥贝球铁衬套材料和金属氟塑料自润滑衬套材料的摩擦磨损性能进行研究.结果表明,金属氟塑料自润滑材料与45钢配副的摩擦系数远远低于奥贝球铁材料与45钢配副,金属氟塑料自润滑材料的耐磨性能也优于奥贝球铁材料.由于金属氟塑料自润滑材料优良的自润滑性能,与其配对的45钢的磨耗量也远远低于与ADI对磨的45钢.     

两种中温固化胶粘剂的剪切疲劳和蠕变性能研究

研究了SY 2 4B胶膜和SY H2糊状胶粘剂的剪切疲劳和蠕变性能。SY 2 4B胶膜和SY H2糊状胶粘剂同为中温固化的结构胶粘剂 ,SY 2 4B胶膜采用橡胶增韧 ,SY H2糊状胶粘剂采用热塑性树脂增韧。SY 2 4B胶膜虽然具有优异的韧性 ,但SY H2糊状胶粘剂的剪切疲劳和蠕变性能优于SY 2 4B胶膜 ,这与增韧剂种类与胶层厚度有一定关系。温度、应力和时间也是影响蠕变量的重要因素     

大攻角流动的非定常特性分析

本文首先通过动态测量手段研究了大攻角流场中的能量成分,分析了各种成分引发的非定常性对大攻角流动的影响。结果表明大攻角流动本身是一种“涡行为”,非定常性对大攻角流动非对称性的影响较弱,影响大攻角流动的本质因素是涡的动力不稳定性对于前体不确定小扰动的响应。     

Study on the breakup lengths of free round liquid jets

IntroductionBreakup and atomization of roundliquidjetshad been widely used in internal combustion en-gines,gas turbines,and liquid rocket engines.Recently,with the development of scramjet en-gines and the deepening of fuel atomization re-search,it attract…     

基于切削热-力耦合效应的表面强化技术及其工艺试验研究

经过对超高强度钢工件高速切削加工表面质量的系统研究,发现在某种特定的切削条件下,工件表面质量将会发生显著改变.该变化不仅表现为表面特征的大幅改善,如表面粗糙度可以控制在0.4μm以下,无宏观裂纹发生等,还表现为表层及次表层显微硬度的明显提高、最大残余压应力深度的大幅增加(达到0.35 mm)以及表面耐磨性能的显著增强等.研究结果表明,合理的切削工艺将极有可能成为一种能够在获得工件结构形状与精度指标的同时,对加工表面表层、次表层的组织特性与工件使用性能产生积极影响的表面强化手段.     

一种基于高分辨率距离像自动目标识别新方法

提出了一种基于高分辨率距离像的联合对准与识别新方法。该方法结合功率变换的使用，在利用8米雷达目标实测数据进行的识别实验中，获得了较高的正确识别率。